Categories: Electronics Projects

Electronics Engineering Projects On Doorbell Circuit

The electronic doorbell in this article is the most simplest among the advance projects in this website. There are many other benefits of the project doorbell. The circuit for the electronic doorbell here will help realise whether the visitor is in front door or in back door. More about there is two LED indicatorwith different colours which provide visual indication to check if anyone had come nor not in your absence.

PART LIST

Transistors
T1,T2,T5 BC148B
T3,T4 BC158B
T6 AC128
Diodes
D1,D2,D3,D4 1N4001
D5 GREEN LED
D6 RED LED
Capacitors
C1,C2,C3 0.01 μF
Resistors
R1,R7,R8.R9,R10 2.2 KΩ
R2 47Ω
R3,R4 100KΩ
R5,R6 10KΩ
R11,R12 330Ω
Miscellaneous
S1 ON/OFF toggle switch for memory
S2,S3 Switch for doorbell
BATT 9-Volt Battery
LS Loud Speaker 8Ω
OTHERS PCB , Connecting Wires,
Hardware,enclosure etc

CIRCUIT DESCRIPTION

WORKING PRINCIPAL

The presented circuit of doorbell in this site is employs a direct couple complementary amplifier and two regenerative latches. The working principal of the circuit doorbell is simple. There are two switches S2 and S3 for FRONT and REAR door respectively. The S1 is open the circuit act as a two-way doorbell. In this case circuit act as a two-way doorbell  with memory, that is the audio alarm indicates whether the visitor is calling from the front door or from back door.

When the S2 is pressed , diode D1 conducts and the complementary amplifier built around transistors T5 and T6 . Now T5 and T6 starts oscillating due to the positive feedback via capacitor C1. In this case low frequency tone is produced which indicates that visitor is a calling form front door. Similarly when switch S3 is pressed then D2 conducts and a high frequency tone is produced to indicate the visitor is calling at the rear door.

In your absence in someone come to your home and call you then it will recorded in its memory. The circuit can provide you an indication on return whether someone had come to your house and called from front door or rear door.To use the memory unit of this circuit you have to switch on the S1 which is the switch for memory. After that whenever someone call you from front door or rear door it will be indicated by the corresponding colour LED to the door. The corresponding LED will be light up and remains in that state until you return to your home. The Circuit can be reset by switching off the memory switch S1.

When switch S1 in keep ON. This case if someone come to your home and press the switch of front door that is S2 then diode D3 conducts through diode D5 and positive pulse is applied to the base of the transistor T2. After that the regenerative pair built around transistor T2 and T4 quickly full conduction and RED LED  that is D6 lights up and remains  in that state until switch S1 is switch OFF. In the same way when someone press the switch of rear door that is S3 diode D4 conducts through resistor R6 and a positive pulse is applied to the base of the transistor T1 then the regenerative pair comprising transistor T1 and T3 suddenly goes into full saturation and the D5 that is GREEN LED lights up and remains in that stat until the memory switch S1 in switched OFF.

If both the LEDs are found glowing on returning from a visit then you may be surmise that the visitor(s) called yo at the both the doors. In this circuit, diode D1 and D2 are necessary to isolate the front switch S2 and the rear switch S3. In same way D3 and D4 are used to isolate the audio section of this circuit from regenerative latches. C2 and C3 are used to avoid false triggering of the regenerative latches by the surge produced when S1 is switched ON, as this is generally caused due to high gain of the transistors.

admin

Share
Published by
admin

Recent Posts

Standby Generators and Custom Commercial Generators for Sale

Humankind has become extremely dependent on electricity, without it we can’t run the household, keep…

4 years ago

Electrical Machine Interview Question And Answer

[1] Define the term synchronous speed [Dec-2003] For synchronous machines there exists a fixed relationship…

7 years ago

Transformer Interview Questions With Answer

We shared a lot of interview questions on electrical machines, power system and power electronics. Today we…

7 years ago

What Is Diesel Power Station

DIESEL POWER STATION A generating station in which diesel engine is used as the prime…

7 years ago

Synchronous Generator Interview Questions

Q:Why syn. generators are used for the production of electricity? A:synchronous machines have capability to…

7 years ago

Hydro Power Station

Hydro-electric Power Station A generating station which utilises the potential energy of water at a…

7 years ago